Q-101Z
Q-101Z is a medium viscosity (90 cPs) ethyl cyanoacrylate adhesive. It is formulated for bonding difficult and porous substrates such as leather, paper and wood.
Q-101Z is a medium viscosity (90 cPs) ethyl cyanoacrylate adhesive. It is formulated for bonding difficult and porous substrates such as leather, paper and wood.
Q-101Z is a medium viscosity (90 cPs) ethyl cyanoacrylate adhesive. It is formulated for bonding difficult and porous substrates such as leather, paper and wood.
Q-101Z is specially designed for gluing absorbent and porous surfaces such as paper, wood and leather. Q-101Z is also suitable for fast bonding of a wide range of plastics, metals, and rubbers.
Los usos más habituales incluyen:

|
Chemical type Ethyl
|
Etilo
|
|
Appearance
|
Clear
|
|
Specific gravity
|
1,06
|
|
Viscosity cPs1
_Rank
_Typical value
|
80 – 120
90
|
|
Tensile strength2 (N/mm²)
|
20
|
|
Fixture time (sec.)
|
3 – 20
|
|
Total cure (hours)
|
24
|
|
Flash Point (° C)
|
> 85
|
|
Shelf life at 5º C (months)
|
12
|
|
Maximum fill gap (mm.)
|
0,15
|
|
Operating temperature range (° C)
|
-50 a +80
|
Curing speed vs. Substratum
It depends on the type (s) of substrate used. Q-101Z is designed for use on a wide variety of surfaces, including acidic ones such as leather and paper. Plastics with low surface energy (polyethylene, polypropylene, Teflon® require the use of a primer.
Cure speed vs. Clearance
Quimilock cyanoacrylates give the best results when gluing parts. The product must be applied in a very fine line in order to guarantee a fast polymerization and a strong bond. Excessive clearances will result in a slower cure speed. Cyanoacrylate activators can be used to greatly increase the cure speed.
Curing speed vs. Environmental conditions
For a cyanoacrylate adhesive to start the curing process, it requires moisture on the surface of the substrates to be bonded. Curing speed is reduced in low humidity conditions. Low temperatures also reduce curing speed. All figures relating to curing speed have been taken at 21° C.
Curing speed vs. Activator
Cure speed in less than 2 seconds can be achieved with most Quimilock cyanoacrylates. The use of an activator can reduce the final bond strength by up to 30%. It is recommended to do a test on the pieces, to measure the effects.
Heat resistance
Quimilock cyanoacrylate adhesives can be used at temperatures up to 80 ° C. At 80 ° C the bond strength will be approximately 70% at 21 ° C. The bond strength at 100 ° C is approximately 50% of the full force at 21 ° C.
Heat aging
Quimilock cyanoacrylates, retained more than 90% of their strength when heated at 80 ° C for 90 days and then tested at 21 ° C. Heating to 100 ° C and then testing at 21 ° C, achieved a strength of initial bonding of about 50%.
Chemical / solvent resistance
Quimilock cyanoacrylates show excellent chemical resistance to most oils and solvents, including motor oil, leaded gasoline, ethanol, propanol, and freon. Cyanoacrylates are not resistant to humidity, nor to the humidity that appears over time.
For safe handling of this product consult the Product Safety Data Sheet.
Cured cyanoacrylate can be removed from most substrates and disassembled parts. It cannot be completely removed from fabrics.
Store in a cool place away from direct sunlight.
Refrigerated at 5 ° C, it provides optimum storage stability.
Available in packages of 20, 50, 100 and 500 gr.